Jun 4 2018
Pelatihan Uninterruptible Power Supply (UPS) Systems Electrical

Uninterruptible Power Supply (UPS) Systems Electrical Training

Course Description Pelatihan Uninterruptible Power Supply (UPS) Systems Electrical

This technical course begins with a discussion of the need for UPS systems. It then covers the relative comparisons between various UPS topologies and their modes of operation. The batteries used for UPS systems are covered next. How a battery works, their maintenance, safety and testing is throughly discussed.

A solid working knowledge of the typical electrical components found within a UPS is developed before exploring how AC is converted to DC and then inverting DC back to AC. When all of the above elements of a UPS are understood, a theoretical rectifier and inverter feedback loop are throughly discussed. This will be followed by a trouble shooting exercise. Students are given failure scenarios where they work in groups to find which circuit component has opened, shorted or significantly changed in value to produce the alarm condition described. The course finishes with a general discussion on UPS system trouble shooting.

Some working knowledge of basic electrical engineering principles is required, although this will be revised at the beginning of the course. Real-life experience in working with batteries and UPS systems will enable the workshop to be placed in context.

Materi Pelatihan Uninterruptible Power Supply (UPS) Systems Electrical

I. Introduction to UPS Systems

    * Power conditioners
* Uninterruptible power systems
* Power quality source alternatives
* Power disturbance cost comparisons

II. Three General Types of UPS’s

    * Kinetic (Motor Generator Sets)
* Flywheel
* Static and Components
* Rectifier
* Batteries
* Inverter

III. Three types of Static UPS’s

    * Traditional UPS
* Static UPS
* Static UPS with Bypass

IV. UPS Operation Overview

    * The Need for UPS System
* Power System Disturbances
* Basic Type of UPS Systems

V. Introduction to Batteries

    * Primary Batteries
* Secondary Batteries

VI. Lead Acid Batteries

    * Chemistry
* Different types
* Capacity Factors
* S-Curves
* Battery Safety and Maintenance
* Float and Equalize Voltages
* Load Testing

VII. Nickel Cadmium Batteries

    * Chemistry
* Battery Types
* Capacity Factors
* Battery Safety and Maintenance
* Float and Equalize Voltages
* Load Testing

VIII. Passive Electronic Components

    * Resistors Circuits
* Capacitor Circuits
* Inductor Circuits

IX. Semiconductors

    * Diodes
* SCR’s
* Transistors

X. Logic Gates

    * AND/NAND Gates
* OR/NOR Gates
* Inverter Gate
* D Type Flip Flop
* XOR/XNOR Gates

XI. Operational Amplifiers

    * Inverting Op Amp
* Non-inverting Op Amp
* Differential Op Amp
* Unity Gain Op Amp
* Summing Op Amp
* Integrating Op Amp
* Comparator Op Amp

XII. AC to DC Conversion

    * Full Bridge
* Three Phase
* Six Pulse

XIII. DC to AC Inversion

    * Quasi Square wave
* PWM waveform

XIV. UPS System Overview

    * Rectifier Stage
* Inverter Stage

XV. UPS System Troubleshooting

    * Basic Use of Test Equipment
* Rectifier Troubleshooting
* Inverter Troubleshooting

Peserta

Peserta dapat diikuti oleh semua yang tertarik pada bidang ini. Selain itu juga dapat diikuti oleh semua yang ingin mengatahui dan mendalami tentang bidang ini.

Instruktur

Instruktur dalam Pelatihan dan Training ini akan dibawakan oleh seorang yang ahli dalam bidang ini.

Metode Training

  • Presentasi
  • Diskusi antar peserta
  • Studi kasus
  • Simulasi
  • Evaluasi
  • Konsultasi dengan instruktur

Jadwal pusattraining.com tahun 2023 :

  • Batch 1 : 24 – 26 Januari 2023
  • Batch 2 : 14 – 16 Februari 2023
  • Batch 3 : 20 – 23 Maret 2023
  • Batch 4 : 4 – 6 April 2023
  • Batch 5 : 15 – 17 Mei 2023
  • Batch 6 : 26 – 28 Juni 2023
  • Batch 7 : 17 – 19 Juli 2023
  • Batch 8 : 14 – 16 Agustus 2023
  • Batch 9 : 25 – 27 September 2023
  • Batch 10 : 10 – 12 Oktober 2023

    Batch 11 : 7 – 9 November 2023

    Batch 12 : 5 – 7 Desember 2023

  • Batch 11 : 7 – 9 November 2023
  • Batch 12 : 5 – 7 Desember 2023

Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta

Lokasi Pelatihan pusattraining.com :

  • Yogyakarta, Hotel Dafam Malioboro (6.000.000 IDR / participant)
  • Jakarta, Hotel Amaris Tendean (6.500.000 IDR / participant)
  • Bandung, Hotel Golden Flower (6.500.000 IDR / participant)
  • Bali, Hotel Ibis Kuta (7.500.000 IDR / participant)
  • Lombok, Hotel Jayakarta (7.500.000 IDR / participant)

Investasi Pelatihan tahun 2023 ini :

Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.

Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.

Fasilitas Pelatihan di pusat training untuk Paket Group (Minimal 2 orang peserta dari perusahaan yang sama):

  • FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara)
  • FREE Transportasi Peserta ke tempat pelatihan .
  • Module / Handout
  • FREE Flashdisk
  • Sertifikat
  • FREE Bag or bagpackers (Tas Training)
  • Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
  • 2xCoffe Break & 1 Lunch, Dinner
  • FREE Souvenir Exclusive

Jadwal Pelatihan masih dapat berubah, mohon untuk tidak booking transportasi dan akomodasi sebelum mendapat konfirmasi dari Marketing kami. Segala kerugian yang disebabkan oleh miskomunikasi jadwal tidak mendapatkan kompensasi apapun dari kami.

Technorati Tags: training production optimization of oil & gas pasti jalan,training optimalisasi produksi migas pasti jalan,training pengenalan production of oil & gas pasti jalan,training gas well loading prediction pasti jalan,pelatihan production optimization of oil & gas pasti jalan,pelatihan optimalisasi produksi migas pasti running

Post Views: 61
pusattra310 0 Comments